Rajiv Gandhi Proudyogiki Vishwavidyalaya 2009 Diploma in Hospital Management Engineering Drawing(CME-202) - Question Paper
MPES/200fi/0234 Tola I Pftfvs : 07
MPECS (HARD CORK)
(CME-202)
(A/c:h/cs/ete/pcr/pt/p/raotd
ENGINEERING DRAWING
Time : Four Hours Maximum Murks . I (JO
Sole : (i) Attempt total su questions. Question No.
1 (objective type) is compulsory. Frorn the remaining questions attempt any five. f 9. TO m ! TO i&TO* 1 (vqfiTO
I 5WT7 3*1) t I *1* *91 %
J TOt \
I (ii) In case of an> doubt or dispute, the English version question should he treated as final, fatft 4 aiw *1 fnrfH it
arir* . to $ tffiro *ht *rtm <
I. Choose the correct answer 2 each
IWT W $1 W 'ftfTTT i
(i) The angle between isometric axis are :
(a) Mt
(h) 45
(c) <*r
(d) 120
frflUrefol MWI f 4N =*! *
<*) Ml (*l 4 V (*0 <r <s) Iif
(ii) A S cm Innp. line represents u length of 5 mm the K I of the scale will he ;
(a) 100 ; 1
(b) 1 : HM)
(c) 10 ; I
(ii) I : 1
5 t=Ni Vst, 3 foft. -rwMt J jtw -fr-fa-T Ktm :
(30 100 ; 1 (*) 1 : 1(H)
PH) 10 : 1 (?) 1:1
(iii) Which of the following is he conic;; section
(a) Cycloid
(h) involute
(c) Spiral 4
(d) 1 Uipse
foHMfof* TR | ?
(M)
(*) &tr*jZ ?
(*T) vmvrn (O rtfam
(iv) A (>oim is 3 cm below H. R and 2 cm in front of V 1* l! is in which quadrant ?
(a) I irst (
i 5>vrfw *
2 (ii f? f? .fvihrf ifpn }
(3?)
(v) The curve traced out hv a point on the circumference of a circle which rolls on a straight line is known xs :
(a) Ellipse {b) Cycloid
3R tfH cf?f fuift iM ?: il V t % fH 71
fHR <51 THT?fT *
I.W) ufT-fl (51)
2 <a) Draw the conventional symmil f the toMowiny :
<ij Class (ii) Hell (til > Lrinai Mall
(iv) Water meiei
(v) (iatc valve
(vi) < Vilni# Ian
MP1S 2008 0234 3 p T 0
fiTMfaftM * M f**
(ii)
(iii) *?r*r
(iv)
(v)
<vi) Wf * W (hi Write the following words in single stroke vc/iitj) capita letter* of 14 mm height 6 INDIAN STANDARD
farfr >!* 14 Mt W
INDIAN STANDARD tc) Draw involute of a pentagon of 40 nui$
Side
6
<HK 40 Mt 41 % *1 pfse i y 1a> OmMruet 4 vernier #calc ol R. F * to
read ccrnimeter and lom enough to me.iMire up to 5 metres. Show a length of
2 2H m on it. 9
0+ jfttfi m ran fsnwj fv=i t
* IM<I rfl I 1W* 228 to itf ?WI< *7T*fT*
(t) I tii* major axis of an ellipse is 140 tnitt long ttfuJ mmoi <*** i VO mm Jong Drw eltipxe hy ' concentric circle" method. V
MP/$/200fl/0234 4
f I
Draw an Isometric view of a cylinder of 80 mm dia and 50 run in height, when its axis is horizontal.
so 50 fWt. km wwflHra flRivn; swfa otsi 3? 4foa iww *1*
(b) A hexagonal lamina ot 15 mm side has one of its coVner in the H. P Its plane is inclined at an angle of 45 to Ii P. and pcfpcmlicular to V. P. Draw its projections.
9
MflRI k 15 Ml I ! fWB - it ftnr r Afinr aw $
Ft* w? aflfatr!
5 (a) A line AB, 50 mm long has its end A in hotfi the H P. and the* V P It is inclined at Mf n> the 11 P. and 45n to the V. P Draw ts projections. *4
So Mt \m \8 ** fim -a $f?r* im
& .*WW !f5f St-ff # f #T4 TO
a#? s-vrivi -m n 45u I: pi*
<b A pentagonal prism, side of base M) mm and **u 60 mm fong is resting on **n edge ot its hast- in the ground with its axi> MPC/6'2000/0234 5 or n
inclined ai W to I! P and parallel to V. fc Draw its projection*. *
tr* M fsm *nm & *o fat
*? 60 Mr sfwft #>, mk ww & r*
t qn aw &ff* vr 9i &1 mm I m 3ilfw W * TTOTIW $ I $m *t i
6. A cone of base dia. 40 mm and height 65 mm is kept on II. P. with its axis perpendicular to
H. P and parallel to V. P. It is cut by cuuiog plane at an angle of 3(f to H P and perpendicular to V. P The cutting plane passes through mid point of the axis. Draw elevation, sectional plan, true shape and develop the lateral surface of the cone. 18
(r*. ft f&v* jrw 40 fa*n. <wi 3?ai? t>5 fa*t k <w m 7W i , m w w
I nm vta ih *. nvrrcra i J7 up* ws ** ra to *. ft f* Afti m* Mt t to wwn w *> mu % w ftp; s 7ptrm $ f %w. qft'dfcv *H asm
virrJ w $R fafcrn ntn*.
7 (a) Uravk the projections of the following points on the same reference line, keeping the projectors 20 mm apart : *>
(i) *A in the II P and 20 mm behind V P
(ii) B M\ nun above II. P .mil nmi mfront of V, P
(iti) t" HO nnn tvUw ihc H P urnt 40 mm behind V P
MPE S/2009/0234 6
Attachment: |
Earning: Approval pending. |