West Bengal Institute of Technology (WBIT) 2009-5th Sem B.Tech Computer Science and Engineering Computer Science - Control System - Question Paper
&
Home:...................... R6UN0.: .............. Invigilator's Signature:
C8/B.Tech(CSE/IT)/SRM-5/EE-503/2009~ 10 2009 CONTROL SYSTEM
Pull Marks : 70
The figures in the margin indicate full marks.
Candidates are required to give their answers in their own words
as far as practicable.
Graph paperfs) and Semi log paper(s) will be provided by the
institution.
GROUP - A ( Multiple Choice Type Questions)
1. Choose the correct alternatives for any ten of the following :
10x1 = 10
1) Feedback control system Is basically
. a) high pass filter b) band pass filter
c) low pass filter d) band stop filter.
ii)
The value of x3/xl is
b) 2 d) 5.
a) 8
c) 12
Hi) If the gain K of the system increses, the steady state em>r of the system
a) decreases
b) increases
c) may increase or decrease
d) remains unaltered.
iv) If some pole of a system lies on the imaginary axis, the system is
a) absolutely stable b) conditionally stable
c) marginally stable d) unstable.
v) The root locus of a system has four separate loci. The system can have t
0 four poles or four zeros
b) four poles & four zeros
c) six poles & two zeros
d) two poles & two zeros.
vi) A system has 14 poles & 2 zeros. The slope of its highest frequency asymptote in its magnitude plot is
a) - 40 dB/decade b) - 240 dB/decade
c) - 280 dB/decadde d) - 320 dB/decade.
vii) The disadvantage (s) of polar plot is (are)
a) plot is cramped of high frequencies
b) the calculations are time consuming for exact plot
c) it is very difficult to calculate gain & phase margin
d) all of these.
CS/B.Tech(CSE/IT)/SEM-5/EE-503/2009-10 vill) Teh number of points encircled by X & Y Is
 |
|
a) 2. 1 c) 1, I d) 2, 2. |
lx) The proportional error device has output as function of a) derivative of error b) Integral of error
- c) error d) none of these.
x) The system response can be tested better with
a) sinusoidal input signal
b) ramp Input signal
c) unit Impulse damping signal
d) exponentially decaying signal.
xi) The input-output relationship of a linear system is given by
a) y = a0Jt2 + + a0
b) ytx+a 0
c) y- axx
d) y = a0.
CS/B.Tech(CSE/IT)/SEM-5/EE-503/2009-10
xii) Regenerative feedback means the output is feedback with
a) positive sign b) negative sign
c) step input d) oscillation.
GROUP -B ( Short Answer Type Questions )
Answer any three of the following. 3x5 = 15
|
2. Determine the transfer function of the system having the following graph. |
 |
3. Calculate the transfer function of the electrical network shown in the figure.
20
A system has G ( s ) = s 2 + 5S + 5 & unity feedback. Find
4.
i) Wn ii) %
Hi) Wd
v) T,.
CS/B.Tech(CSE/IT) / SEM-5/EE-503/2009-10
5. A unity feedback system has
1 ftO
G * s * = s ( s + 6 ) & r ( *) = 4t-Determine,
1) the steady state error
ii) the value of k to reduce the error by 6%.
6. Find the stability of a system having characteristic equation s6 + 2s5 + 7s4 + 10s 3 + 14s 2 + 8s + 8 = 0.
GROUP-C ( Long Answer Type Questions )
Answer any three of the following. 3 x 15 = 45
7. The open loop transfer function of an unity feedback system is given by G ( s ) = s ( x + 0.02 s ) ( 1 + 0 04 s)
Draw the Bode plot. Find gain margin & phase margin. Hence find the value of open loop gain so that the system has a phase margin of 45.
8. The transfer function of an open loop control system is ( s ) s ( s 2 + 4s + 8 ) '
a) Sketch the root loci of the system on a graph paper, touching the following points :
i) Number of the root loci
Hi) Angle of asymptotes & their real axis intercept.
iv) Angle of departure
v) Imaginary axis intercepts
vi) Real axis part of root locus.
b) Find from your sketch, the value of gain k at which dominant pole will have a damping ratio, % = 0*5. Also find the corresponding transient frequency of oscillation.
9. By applying Nyquist criterion, state whether the closed loop system having the following open loop transfer function is stable or not.
G(s)H(s)=(s+i)(s_i)-
10 . a) What is a polar plot ?
b) Draw the polar plot of a first order system.
c) What is the effect on the polar plot if a non-zero pole is added to the transfer function.
d) What is Nichols chart ?
e) What is the application of Nichols chart ?
3+5+2+3+2
a) PID controller
b) Lead-lag compensator
c) AC tachometers
d) Effect of adding poles & zeros to a second order linear system.
55201 7
|
Attachment: |
| Earning: Approval pending. |
