Jawaharlal Nehru Technological University Hyderabad 2008-1st Year B.Tech JNTU Regular s, / ENGINEERING DRAWING - Question Paper
Code No: 07A10291 Set No. 1
I B.Tech Regular Examinations, May/Jun 2008 ENGINEERING DRAWING ( Common to Electrical & Electronic Engineering, Electronics & Instrumentation Engineering and Electronics & Computer Engineering) Time: 3 hours Max Marks: 80
Answer any FIVE Questions All Questions carry equal marks k k k k k
1. The vertex of a hyperbola is 65mm from its focus. Draw the curve if the eccentricity is 3/2. Draw a normal and a tangent at a point on the curve, 75 mm from the directrix. [16]
2. Show by means of a drawing that when the diameter of the directing circle is twice that of the generating circle, the hypocycloid is a straight line. Take the diameter of the generating circle equal to 50mm. [16]
3. (a) A point A is 2.5 cm above the H.P. and 3 cm infront of the V.P. Draw its
Projections.
(b) A point A is 2 cm below the H.P. and 4 cm behind the V.P. Draw its Projections.
(c) Two points A and B are in the H.P. The point A is 30mm in front of the V.P., while B is behind the V.P. The distance between their projectors is 75mm and the line joining their top views makes an angle of 450 with xy. Find the distance of the point B form the V.P. [4+4+8]
4. A line AB 120mm long is inclined at 450 to the H.P. and 30 to the V.P. Its mid point C is in V.P. and 20mm above H.P. The end A is in the third quadrant, and B is in the first quadrant Draw the projections of the line. [16]
5. (a) A regular pentagon of 25mm side has one side on the ground. Its plane is
inclined at 45 to the H.P. and perpendicular to the V.P. Draw its projections.
(b) Draw the projections of a circle of 5cm diameter, having its plane vertical and inclined at 30 to the V.P. Its centre is 3cm above the H.P. and 2cm in front of the V.P. [8+8]
6. (a) Draw the projections of a hexagonal prism of base 25mm and axis 60mm long,
when it is resting on one of its corners of the base on H.P. The axis of the solid is inclined at 450 to H.P.
(b) Draw the projections of a pentagonal prism of base 25mm side and axis 50mm long, when it is resting on one of its rectangular faces on H.P., the axis of the solid is inclined at 45 to V.P. [8+8]
7. Draw the isometric view of a Door-Steps having three steps of 22cm tread and 15cm rise. The steps measure 75cm widthwise. [16]
|
8. Draw the following views of the block shown in figure 8. All dimensions are in mm. |
 |
|
Figure 8 |
(a) Front View.
(b) Top view
(c) Both side views.
[16]
2 of 2
Code No: 07A10291 Set No. 2
I B.Tech Regular Examinations, May/Jun 2008 ENGINEERING DRAWING ( Common to Electrical & Electronic Engineering, Electronics & Instrumentation Engineering and Electronics & Computer Engineering) Time: 3 hours Max Marks: 80
Answer any FIVE Questions All Questions carry equal marks k k k k k
1. The foci of an ellipse are 80mm apart and the minor axis is 55mm long. Determine the length of the major axis and draw the ellipse by concentric-circle method. Draw a curve parallel to the ellipse and 20mm away from it. [16]
2. A circle of 50mm diameter rolls on the circumference of another circle of 175mm diameter and outside it. Trace the locus of a point on the circumference of the rolling circle for one complete revolution. Name the curve. Draw a tangent and a normal to the curve at a point 125mm from the center of the directing circle. [16]
3. (a) A point A is 2.5 cm above the H.P. and 3 cm infront of the V.P. Draw its
Projections.
(b) A point A is 2 cm below the H.P. and 4 cm behind the V.P. Draw its Projections.
(c) Two points A and B are in the H.P. The point A is 30mm in front of the V.P., while B is behind the V.P. The distance between their projectors is 75mm and the line joining their top views makes an angle of 450 with xy. Find the distance of the point B form the V.P. [4+4+8]
4. (a) A 100mm long line is parallel to and 40mm above the H.P. Its two ends are
25mm and 50mm in front of the V.P. respectively. Draw it projections and find its inclination with the V.P.
(b) A line AB, 50mm long, has its end A in both the H.P. and the V.P. Its is included at 30 to the H.P and at 450 to the V.P. Draw its projections. [8+8]
5. A circular plane of 60mm diameter, rests on V.P. on a point A on its circumference. Its plane is inclined at 45 to V.P. Draw the projections of the plane when
(a) The front view of the diameter AB makes 30 with H.P. and
(b) The diameter AB itself makes 30 with H.P. [16]
6. (a) Draw the projections of a triangular prism, base 40 mm side and axis 50 mm
long, resting on one of its bases on the H.P. with a vertical face perpendicular to the V.P.
(b) A cube of 50mm long edges is resting on the H.P. with its Vertical faces equally inclined to the V.P. Draw its projections.
(c) A triangular prism, base 40 mm side and height 65 mm is resting on the H.P. on one of its rectangular faces with the axis parallel to the V.P. Draw its projections. [4+8+4]
7. Draw the isometric view of the ribbed angle plate, Shown in figure 7 All dimensions are in mm. [16]
|
10 |
20 4- | ||
|
1 f | |||
|
20 4-- |
10 | |
|
t 40 1 1F |
/ | |
|
i il |
f
|
1 | |
|
*4- 40 |
Figure 7
|
8. Draw the front view, top view and left side views of V- block as shown in figure.8. All dimensions are in mm [16] |
 |
|
Figure 8 |
2 of 2
Code No: 07A10291 Set No. 4
I B.Tech Regular Examinations, May/Jun 2008 ENGINEERING DRAWING ( Common to Electrical & Electronic Engineering, Electronics & Instrumentation Engineering and Electronics & Computer Engineering) Time: 3 hours Max Marks: 80
Answer any FIVE Questions All Questions carry equal marks
1. (a) Inscribe an ellipse in a parallelogram having sides 150mm and 100mm long
and an inclined angle of 1200.
(b) Draw a rectangle having its sides 125mm and 75mm long. Inscribe two parabolas in it with their axis bisecting each other. [8+8]
2. Draw a hypo cycloid of a circle of 30mm diameter which rolls inside another circle of 160mm diameter, for one revolution counter clock wise. Draw a tangent and a normal to it at a point 60mm from the center of the directing circle. [16]
3. Draw the projections of the following points on the same ground line, keeping the Projectors 20mm apart.
(a) Point C, in the V.P. and 40mm above the H.P.
(b) Point D, 25mm below the H.P. and 25mm behind the V.P.
(c) Point E,15mm above the H.P. and 50mm behind the V.P.
(d) Point F, 40mm below the H.P. and 25mm infront of the V.P. [4x4]
4. A line AB of 70mm long, has its end A at 10mm above H.P. and 15mm in front of V.P. Its front view and top view measure 50mm and 60mm respectively. Draw the projections of the line and determine its inclinations with H.P. and V.P. [16]
5. Draw the projections of a circle of 60 mm diameter, resting on V.P. on a point on the circumference. The plane is inclined at 450 to V.P. and perpendicular to H.P. The centre of the plane is 40mm above H.P. [16]
6. (a) Draw the projections of
i. a cylinder, base 40 mm diameter and axis 50 mm long, and
ii. a cone, base 40mm diameter and axis 50mm long, resting on the H.P. on their respective bases.
(b) A hexagonal prism has one of its rectangular faces parallel to the H.P. Its axis is perpendicular to the V.P. and 3.5 cm above the ground. Draw its projections when the nearer end is 2 cm in front of the V.P. Side of base 2.5cm long, axis 5 cm long.
(c) A cube of 40mm side rests with one of its square faces on the H.P. such that one of its vertical faces is perpendicular to V.P. Draw its projections. The nearest edge parallel to V.P. is 5mm in front of it. [8+4+4]
7. Draw the isometric view of the ribbed angle plate, Shown in figure 7 All dimensions are in mm. [16]
 |
|
Figure 7 |
8. Draw the elevation, plan, left and right side views of the part shown in the figure
8. (All dimensions are in mm). [16]
 |
|
Figure 8 |
2 of 2
Code No: 07A10291 Set No. 4
I B.Tech Regular Examinations, May/Jun 2008 ENGINEERING DRAWING ( Common to Electrical & Electronic Engineering, Electronics & Instrumentation Engineering and Electronics & Computer Engineering) Time: 3 hours Max Marks: 80
Answer any FIVE Questions All Questions carry equal marks
1. (a) Inscribe an ellipse in a parallelogram having sides 150mm and 100mm long
and an inclined angle of 1200.
(b) Draw a rectangle having its sides 125mm and 75mm long. Inscribe two parabolas in it with their axis bisecting each other. [8+8]
2. Draw a hypo cycloid of a circle of 30mm diameter which rolls inside another circle of 160mm diameter, for one revolution counter clock wise. Draw a tangent and a normal to it at a point 60mm from the center of the directing circle. [16]
3. Draw the projections of the following points on the same ground line, keeping the Projectors 20mm apart.
(a) Point C, in the V.P. and 40mm above the H.P.
(b) Point D, 25mm below the H.P. and 25mm behind the V.P.
(c) Point E,15mm above the H.P. and 50mm behind the V.P.
(d) Point F, 40mm below the H.P. and 25mm infront of the V.P. [4x4]
4. A line AB of 70mm long, has its end A at 10mm above H.P. and 15mm in front of V.P. Its front view and top view measure 50mm and 60mm respectively. Draw the projections of the line and determine its inclinations with H.P. and V.P. [16]
5. Draw the projections of a circle of 60 mm diameter, resting on V.P. on a point on the circumference. The plane is inclined at 450 to V.P. and perpendicular to H.P. The centre of the plane is 40mm above H.P. [16]
6. (a) Draw the projections of
i. a cylinder, base 40 mm diameter and axis 50 mm long, and
ii. a cone, base 40mm diameter and axis 50mm long, resting on the H.P. on their respective bases.
(b) A hexagonal prism has one of its rectangular faces parallel to the H.P. Its axis is perpendicular to the V.P. and 3.5 cm above the ground. Draw its projections when the nearer end is 2 cm in front of the V.P. Side of base 2.5cm long, axis 5 cm long.
(c) A cube of 40mm side rests with one of its square faces on the H.P. such that one of its vertical faces is perpendicular to V.P. Draw its projections. The nearest edge parallel to V.P. is 5mm in front of it. [8+4+4]
7. Draw the isometric view of the ribbed angle plate, Shown in figure 7 All dimensions are in mm. [16]
|
|
Figure 7 |
8. Draw the elevation, plan, left and right side views of the part shown in the figure
8. (All dimensions are in mm). [16]
|
|
Figure 8 |
2 of 2
|
Attachment: |
| Earning: Approval pending. |
