Jaypee Institute of Information Technology (JIIT) 2007 M.Tech Computer Science Test 3:CIVIL + ECE + CSE - Question Paper
JAYPEE UNIVERSITY OF INFORMATION TECHNOLOGY
WAKNAGHAT
TEST-3 (Nov. 2008)
M.Tech. 1st Semester Civil Engg.
COURESE NAME : Construction Technique MAX. MARKS : 30
COURSE CODE : 07M11CE101 TIME 1 Hr 30 Min
COURSE CREDIT : 03
Note : Attempt all questions
All questions carry equal marks
Q.1 What are the fire protection requirements for multi storied buildings?
Q.2 Write short note on prefabrication.
Q.3 What are the requirements of innovative construction techniques?
Q.4 Define terrazzo flooring in brief.
Q.5 What do you understand by modular construction?
Q.6 What are the upper floors? Define in brief.
T-3 M.Tech 1 and li.Tect, VII Semester 2008
Subject Code: 08B71EC410
Subject Name: Speech Coding and Processina MaX Marks 30
Max Time 154 Jtre
Attempt all seven questions
q"a"tir be designed Why this
2' dhe SUb'band COdi"8 f Expwn how the optimum bit allocation human spehTiStiowKf inStmment and comPe it with the
4- Describe how the filter bank can be used as a model for the auditory system. W
5. List and explain the linguistic categories for ASR.
6. Explain Dynamic Time Warping. Why is it required? J
7. Describe statistical sequence recognition
Jaypee University of Information Technology Waknaghat
Test3-Advanced Communication Systems (Elective) (07M11EC101)
For MTech and VII Semester ECE students Time lhr 30 min; Marks 30; Nov-Dee 2008 All questions carry equal marks
1. A receiver is made up of the following four stages:
(a) Stage 1 an antenna with a noise temperature of 273K and Aer = 100m2, Poynting vector magnitude = 10_12W/m2, bandwidth=lMHz (Boltzmanns constant=1.38 x 10-23W/K - Hz); (b) Stage 2 gain=20 dB and NF=6 dB; (c) Stage 3 is 3 dB lossy network and (d) Stage 4 is an amplifier of gain=60 dB and a noise figure of 16 dB
(i) Find the power of the signal and SNR at the input and output of every stage
(ii) Repeat (i) with stage 2 removed
2. Consider the parity coefficient matrix P matrix
1 1 1 1 0 1 0 1 1
P =
1 1 0
(a) Find the generator matrix G (b) Find all codewords corresponding to all message words (c) Find H the parity check matrix, (d) Compute the syndromes corresponding to the received codewords 1001101 and 1111000. Are these valid codewords?
3. Using the Gram-Schmidt process of orthnormalisation find the orthonormal waveforms for the waveforms given below:
Si(i) |
S2(t) | |
2 |
t , t | ||||||||||
| ||||||||||
12 t 12 t |
After doing so show how these orthonormal functions may be used in a baseband communication system. |
JAYPEE UNIVERSITY OF INFORMATION TECHNOLOGY
WAKANAGFIAT TEST-3 M.Tech. (CTM) 1st Sem. 2008
Course Code: 07M1 ICE 103 Max.Time: 1 Hr. 30 Mins
Course Name: Construction Planning and Control Max.Marks: 30
Course Credit: 3
Ql. Table below gives the data about durations and costs of various activities of a network.
Activity |
Time in weeks |
Direct costs (Rs.) | ||
Normal |
Crash |
Normal |
Crash | |
1-2 |
4 |
2 |
4000 |
12000 |
2-3 |
5 |
2 |
3000 |
7500 |
2-4 |
7 |
5 |
3600 |
6000 |
3-4 |
4 |
2 |
5000 |
10000 |
The project overhead costs are Rs.2000 per week. Find the optimum duration and the cost associated with it. Also, draw the least cost network.
(20)
Q2. Write short notes on:
a. Importance of site records.
b. Progress recording.
c. Control of resources.
(6)
Q3. What are early warning systems? Explain monthly cost-value reporting and cost value reports.
JAYPEE UNIVERSITY OF INFORMATION TECHNOLOGY, WAKNAGHAT
TEST-3
a
M.Tech. (CTM) 1st semester, 2008
COURSE CODE: 07M11CE105 MAX. TIME: 1 hr. 30 mins.
COURSE NAME: Mechanical and Electrical Systems in Buildings
COURSE CREDITS: 03_MAX. MARKS: 30_
Note: All questions are compulsory. Marks are indicated against questions.
Q. 1. (a) Deduce the emf equation of a transformer. (2)
(b) A single-phase, 250-kVA, ll-kV/415-V, 50-Hz transformer has 80 turns on the secondary. Calculate (i) the approximate values of the primary and secondary currents,
(ii) the approximate number of primary turns, and (iii) the maximum value of the flux.
(1 + 1 + 1 = 3)
Q.2. (a) Draw a typical torque-slip characteristic curve of an induction motor. (2)
(b) A 3-phase, 6-pole, 50-Hz induction motor has a slip of 1 % at no load and 3 % at full load. Find (i) the synchronous speed, (if) the no-load speed, (iii) the full-load speed. (1 + 1 + 1 = 3)
Q.3. (a) Explain with diagrams the following: (a) one-pipe heating system and (b) two-pipe heating system. (3)
(b) Describe the requirements of gas-supply system in a residential building. (2)
Q.4. (a) Write a note on communication installations in a building. (2)
(b) What is rolling sphere theory of lightning? Explain the conventional methods of lightning protection of buildings. (3)
Q.5. Under what circumstances pump is necessary? Explain working of airlift pump with neat sketch. (4)
Q.6 Water is required to be pumped from a well for a colony having population of 10000. Following data are made available. (6)
Rate of water supply = 150 litres/cap/day RL of full supply level of reservoir = 125 m
Maximum rate = 2 times the avg. Length of rising main = 1000 m
Hours of pumping =16 RL of pump = 107 m
RL of bottom of well = 100 m Minor losses = 10%
RL of foot valve = 101 m Friction factor = 0.03
RL of Low water level = 102 m Efficiency of pump sets = 70%
RL of ground level = 106 m Velocity of water at discharge end = 1 m/s
RL of maximum water level = 104 m
Find the horse power of the motor and running cost per month if energy charges are Rs. 2.5 per unit.
JAYPEE UNIVERSITY OF INFORMATION TECHNOLOGY
WAKNAGHAT
Test 3- Nov, 2008 M.Tech 1st Semester
Course Code: 07M11CE102 Max. Marks: 30
Course Name: Estimating & Costing Max. Time: 1 hr 30 min
Course Credit: 3
Note: All Questions are compulsory
Assumption if made should be written explicitly
Q l. A small steel frame structure is to be erected and an estimate of the cost is required. The unloading, erection, temporary bolting, and plumbing will be done by a crew of 1 foreman, 1 crane operator, and 4 structural steel workers with a crawler crane. The bolting will be done by two structural steel crew using power tools. The painting will be done by a crew of 3 painters with spray equipment. For unloading at site erection , temporary bolting and plumbing allow 7 labor hours per ton for the roof trusses and 5 labor hours per ton for the remaining steel. Assume 60 crew hours will be required for bolting and 1.11 labor hours per ton for painting.
Assume appropriate equipment productivity cost, labor cost and cost involved in any type of development process. The profit earned maybe kept as 12 % of all cost.
Given the material required: A 36 structural steel for truss: 15 tons and columns: 50 tons. [8 marks]
Q 2. Prepare analysis of rates for first class brick laid in cement mortar 1: 7 in super structure up to 4 m height. Assume material and labor cost. [ 4 marks]
Q 3. .Explain in detail the procedure for following estimating activities: [ 10 marks]
i. Earth work
ii. Adjustment to parametric data
Q 4. Write explanatory note on the following: [ 8 marks]
i. Time and Location adjustments in estimating
ii. Statistical techniques in CER development.
Jaypee University of Information Technology, Waknaghat
Test - 3 \I.Tech 1st Semester, 2008
Course code: 07M11CE104
Course name: Construction Safety and Health
Note: Attempt all 6 questions. Each question is worth 5 marks.
Q. la Construction by its very nature is hazardous. What are different types of hazards in construction?
Q. lb List the diseases caused during construction.
Q. 2 Describe major elements of worlds best practice in construction safety management.
Q. 3 Author Allan Holt writes, Human error as a simple catch-all explanation for accidents is now discredited. The term, if it means anything at all, does not provide an adequate description of the many ways in which the failure of people at all levels in organization can contribute to the complex phenomenon we call accidents. It is more useful to think about human failure ... The human failure involves
1. Active failures
2 Latent failures
3. Errors
4. Slips
5. Lapses
6. Mistakes 7 Violations
8. Routine violations
9. Situational violations, and
10. Exceptional violations
Define these terms such that the differences between them become clear.
Q. 4 As the key document pulling all the threads of the management process together, the safety policy details the arrangements made to comply with relevant regulations. List three essential elements of a safety policy. Explain each element.
Q. 5a Risk assessments are used to generate method statements. What are method statements?
Q. 5b For difficult to identify hazards, we use inductive analysis. What is inductive analysis?
Q. 6 State 6 important rules for successful meetings
JAYPEE UNIVERSITY OF INFORMATION TECHNOLOGY WAKNAGHAT, SOLAN-173 215, INDIA
Test-3 M. Tech. (1st Semester)
Electronics and Communication Engineering
Course name: Advance Satellite and Fiber Optic Communication Time: lhr.30min
Course code: 07M11 EC 102 Max. Mark: 30
Course credits: 03_
Answer all questions.
Q. N. 1(a) Explain what is meant by orthogonal polarization and the importance of this in satellite communication? [5]
(b) A continuous 12-km long optical fiber link has a loss of 1.5dB/km. (i) what is the minimum optical power level that must be launched into the fiber to maintain an optical power level of 0.3|iW at receiving end? (ii) what is the . required input power if the fiber has a loss of 2.5dB/km? [5]
Q. N. 2(a) Explain what are the important parameters those will examine the design optimization characteristics of single mode fiber? [5]
(b) An 8|am core diameter single mode fiber is having core refractive index of
1.5 and a cladding refractive index of 1.46. Determine the critical radius of curvature at which large bending occur if the operating wavelength is 1.55fj.m.
[5]
Q. N. 3(a) Explain the nonlinear effects on network performance in the fibre optic communication systems. [5]
(b) The directive gain of the antenna is 52dB, and the antenna efficiency is 0.95. What is the power gain of antenna? [5]
JAYPEE UNIVERSITY OF INFORMATION TECIINOGLOGY WAKNAGIIAT, Minor- III, November 2008 M. Tech. CSE, I Sem Course Name: Advanced Data Structures Max. Marks: 30
Course Credit: 3, CoDE : olr<n ci- |o| Max. Time: 90 min.
Question 1. Show that for all n C N, there exists an AVL tree for which the deletion of a node would cause n rotations (single or double). Show how such a tree is constructed, show the node to be deleted and explain why n rotations are necessary and sufficient.
[Marks: 4]
Question 2. In NOIDA toll way the toll collections uses a computerized toll collection system. The highway is modeled as an ordered list of toll booths
ti, t2, t3.....t in which toll t, collects the toll of Rs.tfj 0< /' < n. Design a
Data Structure that can perform the following operation in 0(log n) time.
i. Insert a new toll booth after with toll Rs.o
ii. Delete toll
iii. Add Rs.o to the toll of all the toll booths from t, till tj both included.
[Marks: 8]
Question 3. Given an array a[l...n] of integers, consider the problem of finding the longest monotonically increasing subsequence of not necessarily contiguous entries in your array. For example, if the entries are 10, 3, 9, 5, 8, 13, 11, 14, then a longest monotonically increasing subsequence is 3, 5, 8, 11, 14. The goal of this problem is to find an efficient dynamic programming algorithm for solving this problem.
[Marks: 8]
Question 4. Using depth first search, outline an algorithm that determines whether the edges of a connected, undirected graph can be directed to produce a strongly connected directed graph. If so, the algorithm outputs such an orientation of the edges.
[Marks: 5]
Question 5. Suppose that B-TREE-SEARCH is implemented to use binary search rather than linear search within each node. Show.that this change makes the CPU time required (9(lg n), independently of fiow t might be chosen as a function of n.
[Marks: 2]
Question 6. Show the results of inserting the keys
F, S, Q, K, C, L, H, T, V, W, M, R, N, P, A, B, X, Y, D, Z, E in order into an empty B-tree with minimum degree 2. Only draw the configurations of the tree just before some node must split, and also draw the final configuration.
[Marks: 3]
i
Attachment: |
Earning: Approval pending. |